Sorted:
  • EZlap Timing System
    EZlap Timing System

    X-Racer X-1 Racing with EZlap Timing System The EZlap timing system is a race management system that specially designed for both indoor and outdoor small scale drone racing. This new FPV race tracker allows 4 pilots to race at once. The EZlap timing system comes with a master controller, 3 infrared receiver modules, 8 transmitters. The system is powered by a PC or laptop via a USB cable connecting to the USB port of master controller. It is easy to install, simply mount the master controller and receiver modules in the racing gate, install the transmitters in the racing drones, then install the free RCM Beginner software (can be downloaded at the bottom of this page) in your computer and connect with the provided USB cable, you and your friends will be able to start the racing just in a minute.The master controller sends the signals that received from the infrared receiver modules to the computer after processing.The infrared transmitter is 0.4g only, it will not increase any weight to the racing drone since it is so light in weight. It has 8 different address codes which are switchable via the 3-digit DIP switch. Start to send the address codes after powering on via USB.The infrared receiver modules receive the address codes from the transmitters and send them to master controller.Connection and Use:The master controller is powered by the USB after connecting to the PC. No extra power supplies required.The receiver modules and master controller are connected with three special made 6-pin plug cables. In the EZlap timing kit there are 4 receiver modules (including the master controller) included. But how many modules you need depending on your track width and the height of your bridge. The quantity of receiver modules is also limited by the USB loading capacity.The infrared transmitter is powered by the built-in button cell battery.Connect the master controller to the PC with the provided USB cable, access to the free RCM Beginners software and set the pilots information.Package Inlcuded:Master controller x 1 (similar to receiver module but with a USB port)Receiver module x 3 Transmitter for racing quad x 816cm 6-pin plug camble x 33m long USB cable x 1Downloads:RCM Beginners (Free Software)RCM Beginners User ManualThe master controller is powered by the USB after connecting to the PC. No extra power supplies required. It sends the signals that received from the receiver modules to the RCM Beginners software after processing.The receiver modules are connected by 6-pin plug cables. They receive the address codes from the transmitters and send them to master controller.The infrared transmitter is 0.4g only, it will not increase any weight to the racing quad since it is so light in weight . It has 8 different address codes which are switchable via the 3-digit DIP switch. Start to send the address codes after powering on via USB.Three 16cm 6-pin plug cables are included to connect the receiver modules and master controller.The 3m USB cable is used for connecting the master controller to the PC. All the parts included in the EZlap timing system.Management interface of RCM Beginners.The EZlap timing system is working during the racing.

    Review: Write a Review

    $99.00 $79.00, Save $20.00 OFF

    SKU:FCTR

    Weight: 0.25 kg

  • Matek FCHUB-6S W/ CURRENT SENSOR 184A  BEC 5V & 10V
    Matek FCHUB-6S W/ CURRENT SENSOR 184A BEC 5V & 10V

    The Matek FCHUB-6S PDB distributes power from a 3~6S LiPo pack to 4 ESCs, as well as providing regulated & filtered DC 5V & DC 10V outputs for powering Cameras, RC receiver, Flight Controllers, Video Transmitters, LEDs, etc. It also has built-in 184A current Sensor, and offers a FFC socket to connect the MATEKSYS Flight Controller conveniently.Features:Total 4 pairs ESC solder tabs are fit for X type frameMax.27V input w/ TVS protectionBuilt-in current sensor 184APDB: 4*30A (4*46A, 5 seconds), 4layers*2oz copper PCBBEC 5V/1.5A(2A Max) w/ 100uF panasonic POSCAP filterBEC 10V/1.5A(2A Max.) w/ 47uF TDK MLCC filter5V & 10V Output LED indicators & Short circuit tolerant

    Review: Write a Review

    $9.60 $7.10, Save 26% OFF

    SKU:FCHUB-6S

    Weight: 0.10 kg

  • 12 in 1 Wireless RC Simulator PHoenix RC 4.0/RealFlight G5 G4/VRC/Reflex XTR/AeroFly/FMS
    12 in 1 Wireless RC Simulator PHoenix RC 4.0/RealFlight G5 G4/VRC/Reflex XTR/AeroFly/FMS

    Support the following software:- RealFlight G3 /G4 /G5- PhoenixRC v1.0, v2.0, v3.0 (Automatically update)- PhoenixRC v4.0.k (Only for Windows 7)- Reflex XTR v5.03- AeroFly Professional Deluxe v1.9Specifications:- Color: Red.- Weight: 9g.- Support USB HID1.1 /2.0.Package Included:-  Wireless USB dongle-  USB extension cable-  Audio cable (3.5mm jack to jack plug)-  Servo cable-  DVD discs

    Review: Write a Review

    $15.80

    SKU:WLFSL

    Weight: 0.20 kg

  • FPV PSF power supply LC filter
    FPV PSF power supply LC filter

    This LC filter will remove all bad noice within your FPV setup.This LC filter is absolutly a must when you use only one battery FPV setup.Best results for a FPV setup:1. Twist all powerwires in your FPV setup also servor wires.2. Use LC filter for your Wireless video transmitter power3. Use LC filter for the Camera power4. Use LC filter for the OSD power5. Use as short wires as possible.6. Install High current wires (Main battery/ESC wire) away from all other wires.Without twisting your wires the diffrent FRQ noice will polute the system.Voltage input:3-24V 

    Review: Write a Review

    $8.90 $4.45, Save $4.45 OFF

    SKU:PSF

    Weight: 0.05 kg

  • LPF1400 1.2Ghz Low Pass Filter for solving the issue with 2.4GHz RC Systems
    LPF1400 1.2Ghz Low Pass Filter for solving the issue with 2.4GHz RC Systems

    1.2GHz Low Pass Filter attenuates RF noise which interferes 2.4Ghz RC receivers, tiny and useful, a very nice filter. Helps 1.2GHz Wireless Video Transmitter to prevent unwanted RF noises. 12LPF 1.2G Low pass filters can reduce the interference to 2.4GHz receivers to prevent jitter servo issues. You may install it onto your receivers or transmitters, for filtering out unwanted RF noises1.2Ghz Low Pass Filter for solving the issue with 2.4GHz RC Systems Designed for 910MHz - 1390MHz Wireless A/V transmittersLow insertion loss, less than 0.7dB typical at 1300MHzPassband DC - 1425MHz (<-1.5dB loss)Efficient monolithic LC multi-pole topography designSecond harmonic (> 2.4GHz) attenuation -35dB typicalSMA connectors (male / female)Characteristic impedance 50 ohmHandles RF power up to 8 wattsSmall size, 1.45 x 0.31 x 0.25 inches (37 x 8 x 6.5 mm)Lightweight, 5.45 g

    Review: Write a Review

    $22.90 $9.85, Save 57% OFF

    SKU:LPF1400

    Weight: 0.05 kg

  • HENGE 5v/6v/7.4v 8A UBEC 7V-25.5V Input 2-6 Lipo
    HENGE 5v/6v/7.4v 8A UBEC 7V-25.5V Input 2-6 Lipo

    HENGE 8A UBEC is an external voltage stabilizer, it works at the Switch Mode. It can obtain the suitable DC voltage from 7‐25.5V input voltage for receivers and other device, and steadily provide 8A current to supply power for receiver, gyro, and multi servos. Therefore, the 8A UBEC is very suitable for large electric fixed wing aircraft and helicopters which uses 4S or more batteries. With this UBEC, you can obtain the power for receivers from dynamic power without equipping independent battery pack for receivers.Specifications:- Output voltage: 5V/8A , 6V/8A or 7.4V/8A(changeable with a jumper),Maximum output current: 12A(≤15S)- Input voltage: 7‐25.5V (2—6 cells Lipo battery pack or 6—16 cells NIMH battery pack)- Ripple: <35mVp‐p (@8A/12V)- Size: 45mm*22mm*7.5mm (L*W*H)- Weight: 16gFeatures: 1. Designed with an advanced switching power supply control chip with overcurrent and overheat protection function, the max efficiency of the chip is up to 93%;2. The small size and the light weight make it very convenient to use;3. Provide large output current, the continuous output current is 8A, and the burst output current is 12A, fully guarantee the power demand of equipment.;4. Designed with a high quality switching power supply conversion chip, significantly reduce the electromagnetic interference and ensure the receiver works properly;5. With ultra‐wide input voltage from 7V—25.5V (2—6 cells Lipo battery pack or 6—16 cells NIMH battery pack).

    Review: Write a Review

    $15.99 $11.19, Save 30% OFF

    SKU:HG8AUBEC

    Weight: 0.10 kg

  • Sony F970 battery adapter mounting plate for FPV monitor
    Sony F970 battery adapter mounting plate for FPV monitor

     sony F970  battery adapter mount  for FPV monitor can be used for all of the monitors with VESA standard.voltage output:7.2vspecially designed for FPV monitor.Support SONY F550/570/750/770/960/970 series battery.

    Review: Write a Review

    $9.90 $5.94, Save 40% OFF

    SKU:F970BAMP

    Weight: 0.20 kg

  • $15.00 $4.20, Save 72% OFF

    SKU:DCDC6A

    Weight: 0.10 kg

  • DALRC 20A High Current 3.7-28V Input RC Electronic Switch
    DALRC 20A High Current 3.7-28V Input RC Electronic Switch

    Special features:DALRC 20A High Current 3.7-28V Input remote control Electronic SwitchHigh current, high reliability, support high voltage receivers, compact size, light weight.18AWG silicon wires for power, super soft silicon wires for signal as well. Application examples:Switch for cars/ airplanes lights.Switch for electronic devices like camera, A/V transmitter etc. (connect "positive" wire disconnecting the main power supply,  using common GND wire)Gas/Nitro Engine ignition control, smog control etc.;  You can connect electric heating wire to the device for ignition control. Specifications:Input voltage: 3.7-28VInput current: < 20AControl signal type: PWM signalPower supply wires: 18AWG siliconPower wire total length: 20CM (approx)Weight: 12gDimension: 30 x 16 x 4mm (excluding wires)

    Review: Write a Review

    $7.90 $4.90, Save $3.00 OFF

    SKU:DAL20A

    Weight: 0.05 kg

  • RCA Y Splitter AV Audio Video Plug Converter 1-Male to 2-Female Cable Adapter 2pcs
    RCA Y Splitter AV Audio Video Plug Converter 1-Male to 2-Female Cable Adapter 2pcs

    RCA Y Splitter AV Audio Video Plug Converter 1-Male to 2-Female Cable Adapter100% Brand New.Size: 45 x 25 x 12mmWeight: 7gCompact, Lightweight and easy for storageEasy to use just plug and play.Provide you with the ability to connect RCA cables together in order to extend their length.This RCA AV Splitter can be used as adapter for audio and video connecting.For a higher quality stereo connection on both sides.Strongly shielding from interfering, high fidelity, clear signalConnectors: RCA Male to 2 RCA Femalesone female plug used for monitor(video goggles),the other one used for recording(DVR).Package includes:2 x RCA Y Splitter Plug Adapter 1 Male to 2 Female

    Review: Write a Review

    $1.49 $0.77, Save 48% OFF

    SKU:2-AVC1T2

    Weight: 0.10 kg

  • All-In-One Simulator
    All-In-One Simulator

    This All-In-One Simulator is suitable for the following transmitter: ESky, JR, Specktrum, Futaba, Walkera, etc.It used as a replacement for a lost or damaged USB simulator. Compatible with simulators.-FMS-Reflex XTR 5.03-AeroFly 1.97-Phonix 3.0/4.0-RealFlight G4/G5/G6

    Review: Write a Review

    $9.99 $5.00, Save $4.99 OFF

    SKU:AIOST

    Weight: 0.10 kg

  • Flyduino KISS 24A Mini Power Distribution Board
    Flyduino KISS 24A Mini Power Distribution Board

    ***  FPV Model is an authourized dealer of FLYDUINO KISS. Genuine KISS products guaranteed.Before Purchasing: Please keep the packaging after receiving KISS products. Flyduino, the designer & manufacturer of KISS products, requires original packaging for any return of KISS products.The Flyduino Kiss Carrier Board allows for a clean build of the power supply. This version aims for H-Quad Race Drones/Copters, it is the perfect partner to the KISS 24A Race Edition ESC. 4x KISS 24A RE ESC can be mounted directly on the PDB. The signal lines are then recombined at a comfortable row. So called RECOM (high-quality small switching power supplies) can be installed on the PDB, for example, 5V to provide power for an OSD or a camera.Specifications:Holes: 3x3cm (3.2mm holes)Size: 99.5x45mmWeight: 10gAmps: 120A +PCB with 1.6mm thicknessUser Manual for KISS PDB: 

    Review: Write a Review

    $10.96 $6.96, Save $4.00 OFF

    SKU:KPDB

    Weight: 0.10 kg

Find us on Google+ Watch us on Youtube Like us on Twitter Follow us on Facebook

Home   |   New Products   |   Multi-Rotors   |   FPV Airplanes   |   FPV Gimbal   |   FPV Equipment   |   Battery / Chargers   |   Tools & Accessories   |  Site Map

Product Tags: ABCDEFGHIJKLMNOPQRSTUVWXYZ0-9

Copyright © 2015 FPVMODEL.COM®. All Rights Reserved.