Sorted:
  • X-Racer X-1 F3 Flight Controller V2 with Frsky Rx and OSD Integrated
    X-Racer X-1 F3 Flight Controller V2 with Frsky Rx and OSD Integrated

    The X-Racer X-1 Whoop flight controller is making a return with an all new update. We are always listening to what our customers say and we have made some improvements accordingly. In reality, this is not just a simple whoop flight controller that was designed by us but its more of an FC that has been re-designed by users like you.This micro whoop brushed F3 flight controller was designed for X-Racer X-1, but it also can be used on those micro quadcopters like Tiny Whoop and Blade Inductrix.Features:1. The RX connection protocol has been upgraded from PPM to SBUS. With the SBUS protocol, you are able to get a faster response when the micro racer turn around.2. The integrated OSD (on screen display) is able to show some important flight data on your FPV feed, including battery voltage, current draw etc. You can even use it as a menu to change your quad’s PID, rates, filters and others.3. Larger MOS ensures a smoother flying with your micro racer. 4. The DC regulator module has been upgraded for a better loading capacity.5. Compatible with FrSky & SBUS, USB port ready.6. Pre-flashed with the latest Betaflight firmware.7. The binding buttons for the built-in Frsky RX have been updated, more convenient to use.How to Bind Built-in FrSky RX.1. Press "Band" to power on the quad, the middle red LED will turn on.2. Turn on your FrSky transmitter, set the mode to D8, 1-16CH, and then start to bind.3. After successfuly binding, on the right corner the red LED will start to slowly flash.4. Re-power on the flight controller, the binding is completed.How to Bind other RX.1. Connect the FC to Betaflight.2. Enter following instruction in CLI: set sbus_invention = on. And then save.3. The UART needs to choose 3.(Please take a note that the FC automatically works with the built-in FrSky RX, if you want to use with other RX, please set the CLI before using.)

    Review: Write a Review

    $29.99

    SKU:XR1FCU2

    Weight: 0.10 kg

  • BetaflightF7 RV1 Flight Controller
    BetaflightF7 RV1 Flight Controller

    Betaflight F7 is here and it features a completely new layout. Top mounted solder pads ensure ease of access for the even the trickiest of builds. The Betaflight F7 features dual gyros so the user can have their choice of which one to use, either the tried and true MPU6000, or the ICM20608. You’ll find the specs listed below:Specifications:3-6s Simplistic LayoutTwo Gyro optionsBetaflight OSDFiltered output for FPV systemsSmart Audio/Tramp Telemetry compatibily4 uarts (can read inverted and univerted signals)Camera Control BuzzerBlackbox via flash memory 30.5x30.5 FC mountingBetaflightF7 Setup Guide: Features: Programmable LEDs, Flash Memory, individual pad for camera control, labeled Smart Audio/Tramp TX1 next to VTx soldering pads. Labeled Smart Port TX2 pad next to Sbus/Ibus/DSM2 UART6 Tx, 5v and 3.3v pads (user selection based on type of receiver used), four pads for ESC telemetry connected to RX1.(Each pad placed near corners of the board) By Philipp Seidel, Click to Enlarge

    Review: Write a Review

    $59.99

    SKU:BFF7

    Weight: 0.10 kg

  • BetaflightF4 Flight Controller
    BetaflightF4 Flight Controller

    BetaflightF4 How to ESC Telemetry, Smart Port Audio, Smart Port TelemetryBetaflightF4 is the follow up design to the very popular BetaflightF3. Following in the same path as Betaflight F3 we have kept a very similar footprint in terms of design with a few added modifications. The F405 has replaced the F303 to allow for lower CPU loads.We have eliminated the 5v/3.3v jumper and added two seperate connection points, one for sbus and one for spektrum users. The jumper still remains for the battery voltage/5v connection for connecting your camera. While wiring the board it is recommended to get power for your vtx either from a different 5v source on the board or if using a higher voltage vtx power it from the battery input coming into the pdb. Running ground loop at Agnd with gnd wires from camera and vtx is still recommended to give the cleanest video signal. Another small design change to this board was changing the BEC, this change takes the recommended 5v 2A current limit and drops it down to 5V 1.5A, its a small change but one that we opted for in order to use a more reliable BEC.BetaflightF4 now comes with telemtry pads for BLHeli32 ESCs these pads are located between the signal and gnd pads for the ESC connections.FeaturesIntegrated PDBBuilt in OSD customizable via Betaflight OSDCurrent sensorIntuitive layoutFlash memory for blackboxTailored to support BetaflightWhen running 8K/8K, CPU usage remains low Download Latest Firmware: Betaflight 3.2.0SpecificationsF405 ProcessorMPU6000 Gyro/ACC SensorBEC Max current 5V 1.5ABuilt in OSD – configurable via Betaflight GUICurrent sensorPower distribution board with six-layer PCBOSD Max Current: 145AWiring Diagram - Click to enlarge!

    Review: Write a Review

    $44.73 $33.99, Save 24% OFF

    SKU:BFF4

    Weight: 0.10 kg

  • KISS CompactCTRL CC All-in-One
    KISS CompactCTRL CC All-in-One

    ***  FPV Model is an authorized dealer of FLYDUINO KISS. Genuine KISS products guaranteed.KISS CompactCTRL "CC" (AIOv2) - new Member of the KISS integrated FC&ESCs Family This version of the All-in-One board by Flyduino consists of a KISS 32bit flight controller and 4x 32bit KISS ESCs, rated at 16A (21A active limit), great for mini FPV setups.Its made for instant DIY success as you only need to solder motor wires, connect power and a radio and go. The KISS CC should be ideally driven up to 4s and up to 4 inch props. 5 inch props are possible but you need to choose motors carefully. The CC will actively limit the output to 21A.The CC comes preflashed with FC fw v1.1RC6 and ESC16A fw v110aMore Infos & Downloads: http://kiss.flyduino.net/kiss-compactctrl-cc-allinone-fcescs Specs of the CCWeight of PCB: 11g (without wires)Size 35x42mm (with cut off corners)4x KISS ESC 32bit ESCs 2-4S 16A (21A active current limiter)KISS FC F3 32bit with serial, buzzer and LED ports.Fully Dshot600 capableThe CC supports full telemetry and logging via serial port.Setup is the same as with the regular KISS FC.

    Review: Write a Review

    $97.99 $87.99, Save $10.00 OFF

    SKU:KCCIO

    Weight: 0.10 kg

  • RaceFlight Millivolt Flight Controller
    RaceFlight Millivolt Flight Controller

    MillivoltThe RaceFlight Millivolt flight controller is the most advanced, performance driven, flight controller ever designed in a tiny package. Capable of running 32kHz gyro sample, PID loop, and motor loop, processing all calculations in real time. The Millivolt is truly at the top of its tiny class . The Millivolt uses a F405 MPU and an Invensense 20602 gyro in combination with RaceFlight software to give you the BEST performance possible. This gyro is by far the most noise free and accurate gyro available.PerformanceThe Millivolt presents not only the BEST performance, but also the most STABLE performance due to the amazing vibration rejection technology implemented in RaceFlight. Our filters allow your quad to stay in the air no matter what! Damaged propellers caused by that insane gate clip on turn 3? Not a problem. You can still finish the race! For most people tuning is not even required. Our boards come preloaded with software and defaults that should fly amazing for 99% of people.In addition to the vibration rejection technology, the SSG (Invensense 20602) gives you the highest speeds currently possible with the lowest noise floor and highest sensitivity. The Invensense 20602 gyro has never been used in any flight controller before (except the Revolt) and definitely gives you the leading advantage over others.SoftwareOur flight controller comes pre-loaded with the latest RaceFlight Community release. Just go to the google store and download the latest configurator and you should be ready to connect. Drivers should no longer be needed.RaceFlight One is also available in beta format. Just join our slack at https://raceflight.net/invite/ and ask to be added to the RaceFlight One channel. This is truly amazing software, which flies so well you can completely eliminate prop wash. Setup is a breeze as well, just run a couple wizards and you will get right up into the air.Setup SimplicitySetting up the Millivolt is easy. The solder pin layout is easy to read with motor connections in each corner. Just solder the closest motors and remember the order 1, 2, 3, 4. Select your voltage on the bottom, as well as inverted or not. The Millivolt also features DFU free updating and a self-healing and updating bootloader, just in case something does go wrong.FeaturesIntegrated vibration dampening dummiesInverter for Taranis and Futaba radios3.3v or 5.0v for Spektrum, Taranis, etcLED Driver for WS2812b programmable LEDInfrared LED Race Transponder support – just solder an infared LED to the Revolt and set it up in the RF1 configuratorFuture iPhone and Android configurator supportHigh Speed 32khz gyro, lowest noise floor and highest sensitivity gyro ever usedThrough hole solder pads – forms an I-Beam when soldered for extra strengthFrSky Taranis, Spektrum, Futaba, JR, IBus, Sbus and other radio supportIntegrated buzzer driverVoltage and current ADC pins, for full voltage and current monitoringFull telemetry output supportESC flashing and configuration built into configuratorMost active software developmentSelectable 3.3v or 5v voltage2 serial uartsBluetooth expandableF4 processor16mb of flash memoryGPS expandableDimensions: 25mm x 25mmMounting holes: 20mm squared to center of holes

    Review: Write a Review

    $41.88 $34.34, Save 18% OFF

    SKU:RFMFC

    Weight: 0.10 kg

Find us on Google+ Watch us on Youtube Like us on Twitter Follow us on Facebook

Home   |   New Products   |   Multi-Rotors   |   FPV Airplanes   |   FPV Gimbal   |   FPV Equipment   |   Battery / Chargers   |   Tools & Accessories   |  Site Map

Product Tags: ABCDEFGHIJKLMNOPQRSTUVWXYZ0-9

Copyright © 2015 FPVMODEL.COM®. All Rights Reserved.