Sorted:
  • Wraith32 Metal 32bit BLHELI_32 ESC Dshot1200
    Wraith32 Metal 32bit BLHELI_32 ESC Dshot1200

    The Wraith32 metal is a new 32bit BLHeli ESC that comes with superior quality. Comparing to the standard Wraith32, the Wraith32 metal has following features: The metal MOS has a better heat dissipation and gives more power. More capacitors. Better power supply lines Better stability. Better transmittion interface layoutBLHeli_32 is the third generation BLHeli code, following base BLHeli and BLHeli_S.BLHeli_32 runs on an ARM 32bit MCU, initially it will be on a Cortex-M0 running at 48MHz, but there are MCUs out there that can run a lot faster.So what can the increased MCU speed do?First of all, it can run input signals with lower latency at faster rates. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported.Secondly it allows packing of more functionality. - Like programmable pwm frequency, up to 48kHz, that can run motors even smoother, and also allows for moving of small but potentially disturbing humps in the throttle response. All ESCs have these bumps, with BLHeli_32 they can now be moved in the rpm range, to a place where the system has low sensitivity to them.- Like auto timing. Which is not the option to choose if you’re after max power. But if you want the most efficient running with very good robustness against desync, it is the perfect choice.- Like voltage and current limiting. Which is implemented in the code, and will be supported on some ESCs. Voltage limiting is desirable for fixed wing crafts. And current limiting adds protection against ESC failure.- Like programmable brake on stop force. Which allows control of the braking of fixed wing props.- Like improved direction change in bidirectional mode.- Like more to come in the future. Such as setup from the FC by using Dshot commands. Such as telemetry functionality. There is room to grow performance and functionality.Features:Build in Current sensorOn-Board RGB LED2-6s LIPO input65A designed15*35mmSome Tips:BLHeli_32 ESC Firmware OverviewWhat is Dshot1200 and Why Dshot1200 is Better?How to Get Dshot1200 Running in Betaflight?Downloads:Download the latest BLHeli_32 Configurator here.Download the BLHeli_32 User Manual here.Download Betaflight 3.2.0.

    Review: Write a Review

    $34.99

    SKU:W32MC

    Weight: 0.10 kg

  • Robotdog 35A 32Bit 2-4S BLHeli_32 ESC Dshot1200
    Robotdog 35A 32Bit 2-4S BLHeli_32 ESC Dshot1200

    * MSRP $15.00, for a limited time, the Robotdog is sold at $9.9 only. Dont miss it out if you are buiding on budget.The low price does not mean that the Robotdog is lacking power. It has all features a 32bit BLHeli ESC has!!! 35A designed, ARM 32bit Cortex-M0 MCU, 1500uF cap onboard, 2-4s input and Dshot at least Dshot1200.Robotdog 35A is a new 32bit BLHELI ESC from Battle RC that uses the latest BLheli_32 firmware. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported. If you are seeking for a small, powerful blheli_32 capable 32bit ESCs, the Robotdog ESCs certainly fit the bill providing 35Amps of power.BLHeli_32 is the third generation BLHeli code, following base BLHeli and BLHeli_S. It runs on an ARM 32bit MCU, initially it will be on a Cortex-M0 running at 48MHz, but there are MCUs out there that can run a lot faster. ?BLheli_32 can run input signals with lower latency at faster rates. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported.Here is what BLHELI_32 has to say about their new "Power to perform":Programmable PWM frequency of up to 48KHzAuto-timing for higher efficiency and reliabilityVoltage/Current limitingAdjustable “Brake on Stop” forceImprove direction change in Bidirectional modeConfiguring from FC using DShot commandsFeatures:Blheli_32 codeARM 32bit Cortex-M0 MCUDshot up to at least Dshot12001500uF cap onboard2-4s LiPo input.35A designed32x17 mmSome Tips:BLHeli_32 ESC Firmware OverviewHow to Connect BLHeli_32 ESC to Congigurator BLHelisuite32 via FC PassthroughWhat is Dshot1200 and Why Dshot1200 is Better?How to Get Dshot1200 Running in Betaflight?Downloads:Download the latest BLHeli_32 Configurator here.Download the BLHeli_32 User Manual here.Download Betaflight 3.2.0 here.

    Review: Write a Review

    $15.00-$44.00

    SKU:RD35A

    Weight: 0.10 kg

  • DALRC ENGINE 40A 3-5S 4IN1 ESC BLheli32 DShot 1200
    DALRC ENGINE 40A 3-5S 4IN1 ESC BLheli32 DShot 1200

    DALRC ENGINE 40A 4IN1 ESC adapted 32bit high quality MCU which features more rapidly responeding speed, even smoother handing experience, excellent hardware design with high quality component ensured the powerful performance of ESC, bring you enjoyable flying experience!Features:- Adapting STSPIN32FOA 32 bit burshless motor dedicated high quality processing chip,maximum processing frequency reached to 48MHZ;- Adapting 55 pieces TDK 22UF 25V Low ESR capacitance,total capacity reached to 1150 UF,even lower ripple and higher stability;- Top grade import MOS tube;- 3OZ copper PCB,better operating load capacity;- Up to 5V/3A BEC output.Specification:Item Name: CNC Radiatior DALRC ENGINE 4IN1 ESC Usage: Spare Part for Racing Drone QuadcopterSize:36*36*6mmHole to hole distance:30.5*30.5mm/Φ4.0Weight:16gContinuous Current:40ABurst current(10S):50AInput Voltage:3-5S LipoMcu:STSPIN32FOABEC:5V 3ACapacitance:1150UF Low ESRFirmware:BLHELI 32.XSupports:DShot 300-1200/MultiShot/PWM/OneShotCurrent Sensor: Support

    Review: Write a Review

    $56.99

    SKU:D40ESC

    Weight: 0.10 kg

  • Typhoon32 4in1 BLHeli_32 ESC 4x35A V1.2
    Typhoon32 4in1 BLHeli_32 ESC 4x35A V1.2

    4in1 ESC with 30.5x30.5 mm Mounting holes, supports DSHOT 1200, BLHELI32 firmware.Features:32bit ESC with BLHELI32 firmwareSupports 3-4S lipo input4PWM inputVoltage output (VBAT)NO BECSupports oneshot / Multishot / Dshot PWMMounting holes 30.5x30.5mmSupports damped lightExternal capacitors neededPackage Included:4in1 ESCCapacitoDifferent frame will cause different test result with the current, we rated it as the mid-value, in your frame, the current may higher or lower, there is no Guarantee, if you can get same result in your frame.Notice: There is NO CABLE included.

    Review: Write a Review

    $59.99

    SKU:T32C2

    Weight: 0.10 kg

  • KISS 32A 32bit 2-6S ESC
    KISS 32A 32bit 2-6S ESC

    The KISS ESC 32A powered by a M4 MCU is the new member in the KISS family, developed for race copters with power hungry motor/prop combinations. Actively limited to 45A for longevity it comes with all the features of its little brother, the ESC24A re. With a capacitor it can be driven by up to 6s lipos. This ESC is also compatible with Dshot2400 for an incredibly low response time.Features:- 32-Bit-ARM Cortex M4 MCU @ 80 MHz- Telemetry capability (voltage, current, temperature, rpm)- Over current protection (measures the current and reduces it to max 45A)- Over temperature protection (reduces the max power if hotter then 100°C)- sinHybrid :: Sinwave/BackEMF Hybrid Commutation for smoother running.)- Dshot 2400 (Full resolution of 2000 steps takes only 6.5μs).- Supports all common Dshot commands like turtle mode, 3D mode and rotation direction change.- Expanded adaptive auto timing (3,25-30° advance on each commutation),- For Race Multicopters (32A continuous also with weak cooling),High max. RPM (500.000ERpm, 71.400Rpm with a 14Pole Motor) - Small size (19 x 27 mm)- Accurate RPM control (2000 steps using Dshot)- No additional capacitor needed for 3-5S. Add a min. 220μF min. 50V Cap for 6S usage!- Very fast throttle response, Linear throttle response, Active freewheeling (low diode losses)- Regenerative braking 3-6S LiPo Dshot 100-2400, Oneshot42, Oneshot125 and normal (25 – 500Hz) PWM auto detected.- Supports FrSky Sbus, Graupner SumD, TBS CROSSFIRE and Multiplex SRXL, S-Port, Graupner HOTT, TBS CROSSFIRE and Sensorbus- Operating voltage 9 - 30V (3-6s)- Maximum continuous current 32A, instantaneous maximum current 45A, actively limited- 600000 ERPM maximum rotation field speed (useage up to 500000 recommended)Specifications:Current Draw: 32A Continuous (45A Burst)Voltage Range: 2-6s LipoWeight: 3.3gSize: 20mm x 26mm x 4.5mm

    Review: Write a Review

    $29.89

    SKU:K32C

    Weight: 0.10 kg

  • Wraith32 MINI V2 32bit BLHELI_32  35A ESC
    Wraith32 MINI V2 32bit BLHELI_32 35A ESC

    The Wraith32 Mini V2 35A ESC is an upgraded version of previous Wraith32 Mini 25A. Comparing to the first version, the Wraith32 Mini V2 has more capacitors to help smooth noisy environment, and the data transmission interface is placed outside.Specifications:2-6s LIPO input35A designed10*20mmBLHeli_32 is the third generation BLHeli code, following base BLHeli and BLHeli_S.BLHeli_32 runs on an ARM 32bit MCU, initially it will be on a Cortex-M0 running at 48MHz, but there are MCUs out there that can run a lot faster.So what can the increased MCU speed do?First of all, it can run input signals with lower latency at faster rates. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported.Secondly it allows packing of more functionality. - Like programmable pwm frequency, up to 48kHz, that can run motors even smoother, and also allows for moving of small but potentially disturbing humps in the throttle response. All ESCs have these bumps, with BLHeli_32 they can now be moved in the rpm range, to a place where the system has low sensitivity to them.- Like auto timing. Which is not the option to choose if you’re after max power. But if you want the most efficient running with very good robustness against desync, it is the perfect choice.- Like voltage and current limiting. Which is implemented in the code, and will be supported on some ESCs. Voltage limiting is desirable for fixed wing crafts. And current limiting adds protection against ESC failure.- Like programmable brake on stop force. Which allows control of the braking of fixed wing props.- Like improved direction change in bidirectional mode.- Like more to come in the future. Such as setup from the FC by using Dshot commands. Such as telemetry functionality. There is room to grow performance and functionality.Some Tips:BLHeli_32 ESC Firmware OverviewWhat is Dshot1200 and Why Dshot1200 is Better?How to Get Dshot1200 Running in Betaflight?Downloads:Download the latest BLHeli_32 Configurator here.Download the BLHeli_32 User Manual here.Download Pre-release version of Betaflight 3.2.0 here.

    Review: Write a Review

    $16.99 $14.95, Save 12% OFF

    SKU:W32MV2

    Weight: 0.10 kg

  • Betaflight 32Bit 35A 2-6S BLHeli_32 ESC Dshot1200
    Betaflight 32Bit 35A 2-6S BLHeli_32 ESC Dshot1200

    *** This is the new updated version of Betaflight BLHeli_32 ESC that comes with a line of soldering along the ESC sides for a better protection and giving more power. We are at it again and the guys at Betaflight, FPV Model, BLHeli, and Airbot have come together to create a version of BLHeli_32 ESCs that FPV Model hopes will not disappoint. Introducing a fresh take on an ongoing development with BLHeli_32 we are introducing BetaBees, BlHeli_32 ESCs designed in conjunction with Airbot.BLHeli_32 is the third generation BLHeli code, following base BLHeli and BLHeli_S. It runs on an ARM 32bit MCU, initially it will be on a Cortex-M0 running at 48MHz, but there are MCUs out there that can run a lot faster.  BLheli_32 can run input signals with lower latency at faster rates. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported.Here is what BLHELI_32 has to say about their new "Power to perform":Programmable PWM frequency of up to 48KHzAuto-timing for higher efficiency and reliabilityVoltage/Current limitingAdjustable “Brake on Stop” forceImprove direction change in Bidirectional modeESC TelemetryConfiguring from FC using DShot commandsFeatures: Built in Current SensorExtra capacitors to help smooth noisy envrionments.Customizable color choice RGB LED using Blheli_32 software.Large positive and ground pads for easy soldering. 2-6s Lipo input35A continuous current  (can handle burst above 45A but please be reasonable, do not overwork  your motors)TX pad on ESC used for Telemetry pad. (connect to FC and you would get current sensing, motor RPM, ESC temperature etc)Specifications :Input: 2-6s LiPolyConstant: 35 AmpsBurst: 45 AmpsBEC: No BEC, OPTO onlyDimensions: 34x16x7mmWeight: 6g (without motor wires)Includes:1 x Betaflight BLHeli_32 35A ESC1 x 16AWG Red Silicon Wire 10cm1 x 16AWG Black Silicon Wire 10cm3 x 20AWG Black Silicon Wire 10cm1 x 26AWG Red Silicon Wire 10cmSome Tips:BLHeli_32 ESC Firmware OverviewHow to Connect BLHeli_32 ESC to Congigurator BLHelisuite32 via FC PassthroughWhat is Dshot1200 and Why Dshot1200 is Better?How to Get Dshot1200 Running in Betaflight?Downloads:Download the latest BLHeli_32 Configurator here.Download the BLHeli_32 User Manual here.Download Betaflight 3.2.0 here.We have made a slight change to the second version of Betaflight 32bit BLHeli ESC. The soldering of previous version already connected while the new version not, so as to make the wiring cleaner.

    Review: Write a Review

    $18.99 $16.71, Save 12% OFF

    SKU:BFESC3

    Weight: 0.10 kg

  • X-Racer Quadrant 2-6S 35A 32Bit BLHeli_32 ESC Dshot1200
    X-Racer Quadrant 2-6S 35A 32Bit BLHeli_32 ESC Dshot1200

    Features of New X-Racer Quadrant 35A 2-6S 32Bit BLHeli_32 ESC:Uses the latest BLHeli_32 firmware. Dshot up to at least Dshot1200.At rates up to at least 32kHz is supported.Four tiny ESCs can be installed separately on the arms, or installed together like a PCB under the flight controller.2-6s Lipo input.Rated at 35A current with a max of 50 amps of current load (Less than 10s).Small in size: 20 x 24mm3 grams each piece and about 12 grams for a set of 4 pieces.Compatible to BetaflightF3 Flight ControllerThe new X-Racer Quadrant BLHeli_32 ESC has followed the design of previous 4-in-1 design of X-Racer Quadrant. It is not a single board, but four tiny ESCs can be installed separately on the arms, or installed together like a PCB under the flight controller. This is the 35A version, there is also another 25A version available for your choice.The new X-Racer Quadrant 35A is flashed with the latest BLHeli_32 program. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported. BLHeli_32 is the 3rd generation of BLHeli firmware after BLHeli and BLHeli_S. BLHeli_32 runs on an ARM 32bit MCU, initially it will be on a Cortex-M0 running at 48MHz, but there are MCUs out there that can run a lot faster. The way “pass-through” works is quite similar to previous versions such as BLHeli_S. Basically it uses the flight controller as a programming tool or adapter to allow the computer to talk to the ESC’s directly, so you can change settings or flash new firmware etc.So what can the increased MCU speed do?First of all, it can run input signals with lower latency at faster rates. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported.Secondly it allows packing of more functionality. - Like programmable pwm frequency, up to 48kHz, that can run motors even smoother, and also allows for moving of small but potentially disturbing humps in the throttle response. All ESCs have these bumps, with BLHeli_32 they can now be moved in the rpm range, to a place where the system has low sensitivity to them.- Like auto timing. Which is not the option to choose if you’re after max power. But if you want the most efficient running with very good robustness against desync, it is the perfect choice.- Like voltage and current limiting. Which is implemented in the code, and will be supported on some ESCs. Voltage limiting is desirable for fixed wing crafts. And current limiting adds protection against ESC failure.- Like programmable brake on stop force. Which allows control of the braking of fixed wing props.- Like improved direction change in bidirectional mode.- Like more to come in the future. Such as setup from the FC by using Dshot commands. Such as telemetry functionality. There is room to grow performance and functionality.Software SetupYou will need to flash Betaflight V3.2 or newer firmware on your FC, you can download it from: http://andwho.sytes.net:8080/job/BorisB_BetaFlight/Load the firmware target for your FC locally, and flash (shouldn’t need to short bootloader pins)Download latest BLHeliSuite for BLHeli_32: http://www.blheli32.com/download/Some Tips:BLHeli_32 ESC Firmware OverviewWhat is Dshot1200 and Why Dshot1200 is Better?How to Get Dshot1200 Running in Betaflight?DownloadsDownload the latest BLHeli_32 Configurator here.Download the BLHeli_32 User Manual here.Download Pre-release version of Betaflight 3.2.0 here.

    Review: Write a Review

    $18.85 $16.97, Save 10% OFF

    SKU:XQ35B32

    Weight: 0.10 kg

  • KISS CompactCTRL CC All-in-One
    KISS CompactCTRL CC All-in-One

    ***  FPV Model is an authorized dealer of FLYDUINO KISS. Genuine KISS products guaranteed.KISS CompactCTRL "CC" (AIOv2) - new Member of the KISS integrated FC&ESCs Family This version of the All-in-One board by Flyduino consists of a KISS 32bit flight controller and 4x 32bit KISS ESCs, rated at 16A (21A active limit), great for mini FPV setups.Its made for instant DIY success as you only need to solder motor wires, connect power and a radio and go. The KISS CC should be ideally driven up to 4s and up to 4 inch props. 5 inch props are possible but you need to choose motors carefully. The CC will actively limit the output to 21A.The CC comes preflashed with FC fw v1.1RC6 and ESC16A fw v110aMore Infos & Downloads: http://kiss.flyduino.net/kiss-compactctrl-cc-allinone-fcescs Specs of the CCWeight of PCB: 11g (without wires)Size 35x42mm (with cut off corners)4x KISS ESC 32bit ESCs 2-4S 16A (21A active current limiter)KISS FC F3 32bit with serial, buzzer and LED ports.Fully Dshot600 capableThe CC supports full telemetry and logging via serial port.Setup is the same as with the regular KISS FC.

    Review: Write a Review

    $97.99

    SKU:KCCIO

    Weight: 0.10 kg

  • Wave 4in1 ESC 4x10A 2020
    Wave 4in1 ESC 4x10A 2020

    4in1 ESC with 20x20 mm Mounting holes, supports DSHOT 600, BLHELIS firmwareFeatures:BB21 MCU, 48Mhz Runs BLHELI_S J_H_xx firmwareSupports 2-36S lipo input4PWM inputVoltage output (VBAT)NO BECSupports oneshot / Multishot / Dshot PWMMount holes 20x20mmSupports damped lightNO External capacitors neededDifferent frame will cause different test result with the current, we rated it as the mid-value, in your frame, the current may higher or lower, there is no Guarantee, if you can get same result in your frame.

    Review: Write a Review

    $26.99 $21.05, Save 22% OFF

    SKU:W4I1E

    Weight: 0.10 kg

  • RaceFlight Bolt 4n1 ESC
    RaceFlight Bolt 4n1 ESC

    The RaceFlight Bolt 4n1 electronic speed controller (ESC) provides the power of BlHeli_S performance in a slim package. This makes your electronic stack slim, and generally eliminates the need for an additional PDB. The 4n1 ESC performs great and helps clean up any build.The RaceFlight 4n1 is also extremely easy to install. It is compatible with 4s through 6s batteries and has a built-in current sensor that hooks up directly to the Revolt to provide mAh information. The whole 4n1 ESC pins directly to the Revolt flight controllers and also sends voltage.Specifications30.5mm x 30.5mm mounting hole spacing30 amp continuous draw per motor40 amp burstBlHeli_S5V voltage regulator capable of 3A continuous outputD-Shot ready4s – 6s compatibleBuilt in Current SensorPins to Flight controllerCurrent and Voltage sent to flight controllerEasy InstallHigh-quality components

    Review: Write a Review

    $64.99 $58.49, Save 10% OFF

    SKU:RFB41E

    Weight: 0.10 kg

  • RaceFlight Spark 4n1 ESC
    RaceFlight Spark 4n1 ESC

    The RaceFlight Spark 4n1 electronic speed controller (ESC) provides the power of BlHeli_S performance in a tiny package. This makes your electronic stack small, and generally eliminates the need for an additional PDB. TRFSESChe Spark 4n1 ESC performs great, helps clean up any build, and is perfect for your 3″ build.Specifications:- 20 mm x 20 mm mounting hole spacing- 60A continuous (15A per motor) and 80A burst (20A per motor)- BlHeli_S- 5V voltage regulator capable of 3A continuous output- D-Shot ready- 2s – 4s compatible- Pins to Millivolt Flight controller- Voltage sent to flight controller- Easy Install- High quality components

    Review: Write a Review

    $65.00

    SKU:RFSESC

    Weight: 0.10 kg

Find us on Google+ Watch us on Youtube Like us on Twitter Follow us on Facebook

Home   |   New Products   |   Multi-Rotors   |   FPV Airplanes   |   FPV Gimbal   |   FPV Equipment   |   Battery / Chargers   |   Tools & Accessories   |  Site Map

Product Tags: ABCDEFGHIJKLMNOPQRSTUVWXYZ0-9

Copyright © 2015 FPVMODEL.COM®. All Rights Reserved.