Sorted:
  • RunCam RC25G FPV Lens 2.5mm FOV140 Wide Angle for Swift Series Eagle 4:3 Series Split
    RunCam RC25G FPV Lens 2.5mm FOV140 Wide Angle for Swift Series Eagle 4:3 Series Split

    RunCam RC25G FPV Lens 2.5mm FOV140 Wide Angle for Swift Series Eagle 4:3 Series SplitPackage :1 X Lens1 X Lock Ring

    Review: Write a Review

    $12.99

    SKU:RC25G

    Weight: 0.10 kg

  • Aomway TX004 Mini 5.8G 25mw/100mw/200MW Power Switchable Transmitter
    Aomway TX004 Mini 5.8G 25mw/100mw/200MW Power Switchable Transmitter

    TX004 Transmitter is a 5.8G ISM band simulation diagram transmitter with a stable output power, long-distance transmission,  powerful filter. Can guarantee the image of the maximum throttle no snow, no stripes and so on. TX004 transmitter also has the funtion of remote control the OSD interface and support for more than 8 peoples at the same time flying.Features:-Output power is stable, long-distance transmission: ≥0.5km@25mW, ≥0.8km@100mW, ≥1km@200mW (Original antenna)-Transmit power 4 block switch: 0mW/25mW/100mW/200mW-64 frequency output, has E group of eight competition frequency at the same time without interference-Fast frequency lock-With self-test output power-Video format: NTSC /PAL-Wide input voltage range, low power consumption: 7V~24V,+12V/170mA@200mW.-Small volume: 27mm×27mm×4.5mm-Light weight: ≤3g (Do not including the antenna)Frequency Table:

    Review: Write a Review

    $16.99

    SKU:AWTXT

    Weight: 0.10 kg

  • RunCam TX200 3.5-5.5V 5.8G 48CH 200MW Video Transmitter
    RunCam TX200 3.5-5.5V 5.8G 48CH 200MW Video Transmitter

    TX200 VTX is the first video transmitter from Runcam. It is super light weight and designed specifically for the Runcam Micro Swift 2 camera.The Runcam TX200 is a very simple and plain VTX, there is only one button to change channel, band and power, and some LED’s indicating what settings the VTX is on. The VTX is built on a 19x19mm square PCB and it can be mounted directly on the back of a Micro Swift or Micro swift 2 with the provided standoffs and screws.You can use this VTX as a standalone VTX too if you wish. The standoffs leave a gap between the camera and VTX PCB’s, allows for airflow and better cooling.To know more about Runcam TX200 video transmitter, you can take a reference to Oscar Liangs review.Frequency SetupLock mode:Red LED flashes, only 25mW & limited frequency available;Unlocked mode:Red LED keeps on, 200mW & all 48 channels available; By long pressing button for 10 seconds, you can switch between the two modes.Note: Before you get TX200 unlocked, it is highly recommended to know about the rules and regulations in your country about the frequency to avoid a fine or confiscation of your device.1 Blue LED for ChannelShort press the button to switch the Channel, Channel 1/2/3/4/5/6/7/8 in sequence. For each short press, the Blue LED flashes once, and only when its under the Channel 1, the LED is always on.6 Red LED for BandLong press the button two seconds to switch the Band, Band 1/2/3/4/5/6 in sequence.For each long press, the six Red LEDs light in turn.1 Orange LED for PowerLong press the button five seconds to switch the power, on is 200mw, off is 25mw, lock mode is limited to 25mw.Frequency TableParameter

    Review: Write a Review

    $14.99

    SKU:RCTX200

    Weight: 0.14 kg

  • Set of Flight Controller, Camera, TX and Antenna for X-Racer X-1
    Set of Flight Controller, Camera, TX and Antenna for X-Racer X-1

    This is the accessories kits for X-Racer X-1 and DIY purpose.  Including Flight Controller, Camera, TX and Antenna. These parts have been soldered and tested before shipping.Features:1. Pre-flashed with the latest Betaflight firmware. 2. Micro 5.8g 48ch Vtx. 3. FC is compatible with FrSky & SBUS, USB port ready.4. Micro FPV HD Camera.

    Review: Write a Review

    $56.99

    SKU:X1FC1

    Weight: 0.25 kg

  • BattleRC 60mm Micro 5.8G FPV VTX Linear Antenna Ipex 3pcs
    BattleRC 60mm Micro 5.8G FPV VTX Linear Antenna Ipex 3pcs

    Specifications:Frequency: 5.7~5.9Ghz VSWR:  ≤2.5 @5700 MHz ~5900 MHzGain definition: 2dBi ( *Typical* )Band definition: 4900 MHz ~5900 MHzImpedance definition: 50 ohmSignal transmission directionality: High Gain omnidirectional antennaConnector type: Ipex connector Antenna Length: 60MM

    Review: Write a Review

    $12.50 $6.75, Save 46% OFF

    SKU:3RG178

    Weight: 0.10 kg

  • BattleRC Micro 5.8G FPV VTX Antenna 60mm 3pcs
    BattleRC Micro 5.8G FPV VTX Antenna 60mm 3pcs

    Electrical Specifications:Frequency Range (MHz): 5100-5150/5750-5800Bandwidth (MHz): 50/50Input Impendence (Ω): 50V.S.W.R: ≤1.5Gain (dBi): 2.0Polarization Type: Vertical polarizationLightning Protection: DC groundingPower Capacity (w): 50Mechanical Specifications:Antenna Length (mm): 60MM±1MMRadiator: CuprumConnect Type: WeldingWorking Temp(℃): -40~60Storage Temperature(℃): -20~40Weight (g) :0.5±1

    Review: Write a Review

    $12.50 $7.50, Save 40% OFF

    SKU:3FMQA

    Weight: 0.10 kg

  • Matek FCHUB-6S W/ CURRENT SENSOR 184A  BEC 5V & 10V
    Matek FCHUB-6S W/ CURRENT SENSOR 184A BEC 5V & 10V

    The Matek FCHUB-6S PDB distributes power from a 3~6S LiPo pack to 4 ESCs, as well as providing regulated & filtered DC 5V & DC 10V outputs for powering Cameras, RC receiver, Flight Controllers, Video Transmitters, LEDs, etc. It also has built-in 184A current Sensor, and offers a FFC socket to connect the MATEKSYS Flight Controller conveniently.Features:Total 4 pairs ESC solder tabs are fit for X type frameMax.27V input w/ TVS protectionBuilt-in current sensor 184APDB: 4*30A (4*46A, 5 seconds), 4layers*2oz copper PCBBEC 5V/1.5A(2A Max) w/ 100uF panasonic POSCAP filterBEC 10V/1.5A(2A Max.) w/ 47uF TDK MLCC filter5V & 10V Output LED indicators & Short circuit tolerant

    Review: Write a Review

    $9.60 $7.10, Save 26% OFF

    SKU:FCHUB-6S

    Weight: 0.10 kg

  • Matek FC Vibration Damping M3 Standoff
    Matek FC Vibration Damping M3 Standoff

    Matek M3 vibration damping standoffs help to reduce vibrations on your camera or flight controller.Includes:- 4pcs M3*7*4.5 mm Rubber Vibration Damping Standoffs

    Review: Write a Review

    $2.79

    SKU:MKVDS

    Weight: 0.10 kg

  • Matek  WS2812B RGB 5050 LED Board for FPV RC Multicopter
    Matek WS2812B RGB 5050 LED Board for FPV RC Multicopter

    Specifications:- Power supply voltage: +3.5~+5.3 V- Input voltage: -0.5~+0.5 V- Operation junction temperature:-25~+80 ℃- Storage temperature range:-55~+150 ℃- Can be used for NAZE 32- Size: 51mm*10mmApplications- Naze 32 LED Strip with CleanFlight, AVR, Arduino, PIC, mbed, etcNote : only the LED board

    Review: Write a Review

    $4.90 $3.43, Save 30% OFF

    SKU:WS2812B

    Weight: 0.05 kg

  • 12 in 1 Wireless RC Simulator PHoenix RC 4.0/RealFlight G5 G4/VRC/Reflex XTR/AeroFly/FMS
    12 in 1 Wireless RC Simulator PHoenix RC 4.0/RealFlight G5 G4/VRC/Reflex XTR/AeroFly/FMS

    Support the following software:- RealFlight G3 /G4 /G5- PhoenixRC v1.0, v2.0, v3.0 (Automatically update)- PhoenixRC v4.0.k (Only for Windows 7)- Reflex XTR v5.03- AeroFly Professional Deluxe v1.9Specifications:- Color: Red.- Weight: 9g.- Support USB HID1.1 /2.0.Package Included:-  Wireless USB dongle-  USB extension cable-  Audio cable (3.5mm jack to jack plug)-  Servo cable-  DVD discs

    Review: Write a Review

    $15.80 $14.38, Save 9% OFF

    SKU:WLFSL

    Weight: 0.20 kg

  • Matek RGB LED Board 5050 5V for FPV Multicopters and Planes
    Matek RGB LED Board 5050 5V for FPV Multicopters and Planes

    Matek RGB LED Board 5050/5V comes with three RGB5050 beads. Seven colors are selectable by means of code switches. This LED board will give an eye-catching effect to your multirotors and planes when illuminated.Specifications:INPUT: 4~6V DCSize: 42*10mmWeight: 2gPacking:  LED BOARD 5V, 1pcs,  Cable 0.3mNotes:Comes with a 0.3m long cable, users can cut it to a suitable length;Be ware of the positive and negative poles, as well as the insulation;Switch the related codes to ON, seven colors are selectable;The input is in a range of 4~6V. Can be powered by RX, but please make sure the output current of BEC is enough.Selectable Colors:B ON =Blue, 0.35WR ON =Red, 0.35WG ON =Green, 0.35WB+R =Megenta, 0.70WB+G =Cyan, 0.70WR+G =Yellow, 0.70WB+R+G =White, 1.05W

    Review: Write a Review

    $2.90 $2.55, Save 12% OFF

    SKU:RGB5050-5

    Weight: 0.05 kg

  • Matek RGB LED Board 5050 12V for FPV Multicopters and Planes
    Matek RGB LED Board 5050 12V for FPV Multicopters and Planes

    Matek RGB LED Board 5050/12V comes with three RGB5050 beads. Seven colors are selectable by means of code switches. This LED board gives an eye-catching effect to your multirotors or planes when illuminated.Specifications: INPUT: 10~13V DC Size: 47*10mm Weight: 2g Packing:  LED BOARD 12V, 1pc,   Cable 0.3mNotes:Comes with a 0.3m long cable, users can cut it to a suitable length;Be ware of the positive and negative poles, as well as the insulation;Switch the related codes to ON, seven colors are selectable;The input is in a range of 10~13V DC, can be powered by 3S Lipo or 12V BEC.Selectable Colors:B ON =Blue, 0.35W, 0.03AR ON =Red, 0.35W, 0.03AG ON =Green, 0.35W, 0.03AB+R =Megenta, 0.70W, 0.06AB+G =Cyan, 0.70W, 0.06AR+G =Yellow, 0.70W, 0.06AB+R+G =White, 1.05W, 0.09A

    Review: Write a Review

    $2.90 $2.55, Save 12% OFF

    SKU:RGB5050-12

    Weight: 0.05 kg

Find us on Google+ Watch us on Youtube Like us on Twitter Follow us on Facebook

Home   |   New Products   |   Multi-Rotors   |   FPV Airplanes   |   FPV Gimbal   |   FPV Equipment   |   Battery / Chargers   |   Tools & Accessories   |  Site Map

Product Tags: ABCDEFGHIJKLMNOPQRSTUVWXYZ0-9

Copyright © 2015 FPVMODEL.COM®. All Rights Reserved.