Sorted:
  • Hard Metal 2.1mm/3.1mm Wheel Chock For RC Plane Landing Gear DIY
    Hard Metal 2.1mm/3.1mm Wheel Chock For RC Plane Landing Gear DIY

    pore diameter:2.1mm/3.1mm (optional)Hard Metal 2.1mm/3.1mm Wheel Chock For RC Plane Landing Gear DIY

    Review: Write a Review

    $3.90

    SKU:WC21

    Weight: 0.10 kg

  • Tail wheel landing gear for skywalker 1680 etc
    Tail wheel landing gear for skywalker 1680 etc

    Tail wheel landing gear for skywalker 1680,it also suit to other planes which the fuselage is approximate to the skywalker 1680.we suggest you use it with our skywalker landing gear 

    Review: Write a Review

    $4.50 $3.96, Save 12% OFF

    SKU:TWLG

    Weight: 0.10 kg

  • Snap Ring C-clips For motor 3.17mm/4.0mm 10PCS
    Snap Ring C-clips For motor 3.17mm/4.0mm 10PCS

    The snap ring suits for all the motors with 3.17/4.0mm shaft diameter.

    Review: Write a Review

    $2.90 $2.15, Save 26% OFF

    SKU:SR317

    Weight: 0.10 kg

  • Spring RC SM-S4306R 360 Degree Continuous Rotation Robot Servo SMS4306R
    Spring RC SM-S4306R 360 Degree Continuous Rotation Robot Servo SMS4306R

    Spring RC SM-S4306R 360 Degree Continuous Rotation Robot Servo SMS4306Rparameter:Working Voltage: 4.8-7.2VWorking current: 0.1-1.2 ATorque: 5kg-cm @ 4.8V ; 6.2kg-cm @6VAverage speed: 55 rpm-6VRotation range: 0- 360Working Temperature: 0℃~55℃Size: 40.2mx 20.2 x 43.2mmWeight: 41gConnection Pin OutBrown - GNDRed-VCC (4.8-7.2V)Orange-Signal 

    Review: Write a Review

    $11.90 $7.38, Save 38% OFF

    SKU:SMS4306R

    Weight: 0.10 kg

  • Rubber Bands for RC Plane 6Pcs
    Rubber Bands for RC Plane 6Pcs

    High elastic and quality rubber bandsSize: 1 x 20cm (single side)Color: OrangeUsage: Can be used for remote control airplane models to wings and propeller fix.Package Included:6 x Rubber Bands

    Review: Write a Review

    $3.90 $3.78, Save 3% OFF

    SKU:RB-6

    Weight: 0.10 kg

  • Henge MS522 13g/2.3kg High Speed Metal Gear Micro CCPM Swash Servo
    Henge MS522 13g/2.3kg High Speed Metal Gear Micro CCPM Swash Servo

    Parameter:Product Dimensions: 22.5 * 11.5 * 24.6mmProduct weight: 12gConnection length: 21CMCharacteristics:-Use metal gears, especially use steel material in output gear, which has better intensity, makes sure servos output deviation very small after long time running.-Use high quality motors, makes sure the servos life longer than normal analog servos.-Supply 2.3kg cm torgue; designed for special occasions which need hig torgue; be suitable to be used in 450 dynamoelectric helicopters to control the inclined dishes and in fixed wing airplanes.

    Review: Write a Review

    $11.90 $8.09, Save 32% OFF

    SKU:MS522

    Weight: 0.10 kg

  • MFD MyFlyDream Autopilot OSD Flight Stablizer 2014
    MFD MyFlyDream Autopilot OSD Flight Stablizer 2014

    Please connecting the airspeed meter to aux channel.MAIN FEATURES All In One design. AutoAntennaTracking/AHRS based AutoPilot(3-Axis gyro+accelerometer+magnetic compass + barometer)/Advance OSD/Power module/... are all built in this small,light unit.Fully compatible with AAT systemRich extension ports for Sonar/Air Speed Sensor/Other accessories.AHRS is build-in with Anti-vibration design, easy to install on the plane without any damper.Compatible with MAVLink protocol. Support APM Planner GroundStation software. You can synchronize the waypoints by clicking one button. There are also some GS Apps for mobile phones available.Support PPM/PWM input.All functions/parameters can be accessed by the transmitter and OSD menu.The first AutoPilot transmitting downlink data for tracking via both VIDEO and AUDIO signals.Shipped with customized shielded cables for camera/video transmitter, GPS, 100A current sensor and USB programmer for firmware update. easy to setupSPECIFICATION Power supply: 7~20V (recommended 12V)Current consume: <200ma@12V(included GPS, without other electronics) PWM input channels 6 (PWM input setup) or 8(PPM input setup)PWM output channels: 4Maximum rolling angular: 2000 degree/SFlight modes: MANual, STaBlizer, CIRcle, WayPoinT, ReturnToHome Max Waypoints: 10Support plane layouts: Normal, Wing, V-TailUpdate on November 2nd, 2015: Upgrade the USB. MFD Autopilot Manual EN_download

    Review: Write a Review

    $199.00 $175.12, Save 12% OFF

    SKU:MFDFS100A

    Weight: 0.40 kg

  • MyFlyDream  GPS Module for MFD Autopilot, TeleFlyPro, V5 AATDriver
    MyFlyDream GPS Module for MFD Autopilot, TeleFlyPro, V5 AATDriver

    UBloxDuoTracking3.3V~5V power supply.output NMEA data @ 38400bps, 10Hz rate.For MFD AUTOPILOIT ,TeleFlyPro OSD , and V5 AATDriverUpdate on August 3rd: Add the Duo TrackingGPS to use with MFD AATDriver.It has been configured to 19200bps/NMEA, and has a 6pin connector to connect to AATDriver.After plug this GPS to AATDriver the AAT system "DuoTracking" function is activated. The tracker knows where it is and will keep tracking even when its moving on a car. And you dont need to SetHome before take off anymore.How to check if the GPS is correctly connected with AATDriver:Hold the HOME button on AATDriver. If the local GPS is recognized, you will see a message in the middle of the OSD screen

    Review: Write a Review

    $36.00 $30.60, Save 15% OFF

    SKU:MFD10HGPS

    Weight: 0.10 kg

  • HENGE MD260 260 Degrees Metal Digital Servo for FPV Pan Tilt Control (Upgrade MD180)
    HENGE MD260 260 Degrees Metal Digital Servo for FPV Pan Tilt Control (Upgrade MD180)

    Metal gear servo. Only 12 grams.1.Max rotation :260 degree (end point to 140%)2.Torque:2.0 kg.cm /6V. 1.8kg.cm/4.8V3.speed:0.12 sec/60 degree4.weight :12g 5.working voltage:4.5~6V 6.working current:50-100mah 8.Gear: metal 9 . size: 22.5x11.5x24.6mm

    Review: Write a Review

    $16.90 $12.51, Save 26% OFF

    SKU:MD260

    Weight: 0.20 kg

  • HobbyWing FlyFun 40A Brushless Speed Controller ESC Built in BEC 5V/5A (2-6S)
    HobbyWing FlyFun 40A Brushless Speed Controller ESC Built in BEC 5V/5A (2-6S)

    1  Specification1.1 Output:  Continuous 40A, Burst 55A up to 10 seconds.1.2 Input Voltage:  2-6 cells lithium battery or 5-18 cells NiCd/NiMh battery.   1.3 BEC:         FlyFun-40A: 5A / 5V switching mode BEC..1.4 Refresh rate of the throttle signal: 50Hz to 432Hz.1.5 Max Speed:  210000rpm for 2 Poles BLM, 70000rpm for 6 poles BLM, 35000rpm for 12 poles BLM.      (BLM = BrushLess Motor)1.6 Size:         FlyFun-40A: 60mm*28mm*15mm.1.7 Weight:         FlyFun-40A: 38.8g.2  Features2.1 Safety arming feature:  Regardless the throttle stick position, the motor will not spin after battery connected. 2.2 Throttle calibration funtion: Throttle range can be calibrated to be compatible with different transmitters.2.3 User programmable. 2.4 Multiple program methods supported: transmitter stick, LED Program Card. Very easy to program the ESC at home or at the flying field.2.5 Compatible with Lipo battery and NiCd/NiMH battery.2.6 Internal timing can be changed to be suitable for different brushless motors.2.7 Full protection: Low voltage cutoff protection / Over-heat protection / Throttle signal loss protection.2.8 Extreme low resistance PCB is used at the power output section, the whole ESC has super current endurance capability.2.9 Microprocessor uses separate voltage regulator IC, with good anti-jamming capability.

    Review: Write a Review

    $29.00 $25.52, Save 12% OFF

    SKU:HWFF40A-U

    Weight: 0.20 kg

  • FY 41AP-A&OSD Autopilot For Fixed Wing
    FY 41AP-A&OSD Autopilot For Fixed Wing

    Brief Introduction       FY-41AP is an inertial attitude measurement instrument used for FPV flight on fixed-wing aircrafts and multi-rotors aircrafts. It has an integrated OSD video overlay system that presents critical flight information such as power management, airspeed, altitude, and flight direction via its electronic compass, allowing for a clear visual flight while ensuring key information is within sight.       Flight stabilization is achieved via an integrated 3 axis gyro, 3 axis accelerometer, 3 axis magnetometer and a barometric pressure sensor. This enables the module to accurately measure flight attitude, earth azimuth & relative altitude to achieve:Extremely stable conventional flight patternStabilized 3D flightAutomatically return to home (RTL)Fixed altitude flightHeading lock flightGPS waypoint flightAuto circling over a fixed GPS location. Function Introduction    ● Deactivated Mode - In this mode, the FY-41AP auto stabilization is turned off. The aircraft is completely under pilot control.    ● Stabilized Mode - Level flight is automatically maintained, making flight simple, especially for beginners. If a pilot feels the plane is out of control, simply reduce input control and the plane will automatically recover level flight.    ● 3D Mode - If no input is given by the pilot (all sticks in the middle position), 3D mode will lock the current aircraft attitude. Therefore the aircraft can be easily maneuvered to complete a variety of 3D flight with added stability & smoothness.    ● Fixed altitude & Heading lock Mode - This mode maintains aircraft flight course & holds the altitude on activation. By using GPS data, the system automatically corrects flight course deviation & maintains straight-line flight.    ● Waypoint Navigation Flight Mode - Enable you to fly fully autonomous, with up to 20 waypoints settings via the FY Ground Control Station (GCS) software.    ● Auto Return To Launch Mode (RTL) - Upon activation of this Mode, the aircraft will automatically return to the Home point, maintaining its current altitude. Upon reaching the Home point, it will initiate auto circling. > Related download for fix-wing :FY-41AP firmware for fix-wing V1.16 :DownloadFY module firmware upgrade software and manual :DownloadThe latest FY-DOS&41AP-SETTING software V1.11 for fix-wing :DownloadFY-41AP manual for fix-wing: Read online More FY-41AP related downloads: Click in OSD Video Overlay System Function    ● First Person View (FPV) - FY-41AP has an integrated OSD video overlay system that presents critical flight information on the video for easy enjoy FPV, at the same time, Auto stable, Fixed altitude & Heading lock, Waypoint Navigation , Auto Return To Home function will make FPV operation more easy.        OSD is an essential part for FPV. The FY-41AP can adapt both PAL and NTSC video signals. The entire adaptive process is completed approximately within 1 second.        Integrated OSD Video Overlay System, FY-41AP overlays flight telemetry information onto video image. Information displayed includes: Altitude, Speed, Direction, Home Direction and many more. You should to do the firmware upgrade separately for FY-41AP-OSD control module and OSD module. UART2 is the interface connects to the PC computer serial port to do the firmware upgrade for FY-41AP OSD module.If you want to upgrade the firmware of  flight control part ,pleaseclick on here. FY-41AP OSD display part firmware V1.13 : DownloadFY module firmware upgrade software and manual :DownloadBasic PerformanceSupported aircraft :         1, Normal / Traditional fixed-wing planes;         2, Delta-winged plane with rudder;         3, Delta-winged plane without rudder;         4, Plane without aileron;         5, V-tail plane with aileron;         6, V-tail plane without aileron;Supported servo output: 50Hz refresh frequencyRecommended Transmitter: PCM or 2.4GHz with minimum 6 channelsFY-41AP Module Working Voltage: 5.3V@0.2A( Powered by Power Manager)Air speed senor:0 ~ 200KM/hPower Manager:        Working Voltage Range: Power of battery 7~26V (2S ~ 6S)        Measuring current:0~100A        Power for FY-41AP module:5.3V@2A        Power for Video transmission system :12V@2AOperating Temperature: -10°C ~ 50°CAssistant Software System Requirement: Windows XP sp3 / Windows 7 / Windows 8 Flight PerformanceNavigation Accuracy : Heading:±5°, Rout deviation:±15m (GPS Mode)Max Gyro Angular Velocity: 2000°/sAltitude hold: ±10m Hardware● Weight&Dimensions:FY-41AP: 34g (58×37×19mm);GPS :24g (32×32×13.5mm);Air speed senor:9g (64×13.5×13.5mm);Power Manager:35g(50×24×18mm); GCS ground station software, used to set the flight parameters, mission planning, monitoring in flight. Software integration of electronic map function can through the map software () the Google earth live map out into the GCS software. The main function is    - Parameter Settings — Control parameters setting, course setting, etc    - Real time monitoring — It can monitor flight attitude. And via the GCS software you can change the flight altitude in real time and realize the mouse click flight.    - Record and monitoring flight —You can monitor and download flight path via the GCS software in your computer.GCS 5.1 Software:   Download quickly   |  DownloadNote: Before using FY GCS above 4.11 version, please make sure that the firmware of FY-41AP is the latest version!More versions of the GCS software, please   click in 

    Review: Write a Review

    $249.00 $206.67, Save 17% OFF

    SKU:FY41AP-A

    Weight: 0.50 kg

  • EMAX ES08MD Mini Metal Gear Digital Servo 12g/ 2.4kg 0.10 sec
    EMAX ES08MD Mini Metal Gear Digital Servo 12g/ 2.4kg 0.10 sec

    EMAX ES08MD Mini Metal Gear Digital Servo 12g/ 2.4kg 0.10 secEMAX ES08MD Digital Servo Specifications:   - Type: ES08MD- Operating voltage: 4.8V~6.0V- Operating speed: 0.10sec/60o at 4.8V; 0.08sec/60o at 6V- Stall torque: 2.0/2.4 kg.cm 27.8/33.3 oz.in (4.8V/6v)- Dead band: 1 uSec- Gear Material: Metal- Connector wire length: 25 cm- Connector type: Futaba/JR compatible - Size: 32 x 11.5 x 24 mm(1.25 x .45 x .94in)- Weight: 12g / 0.42ozPackage included:   - 1 x Emax-ES08MD Servo

    Review: Write a Review

    $9.90 $6.34, Save 36% OFF

    SKU:ES08MD

    Weight: 0.10 kg

Find us on Google+ Watch us on Youtube Like us on Twitter Follow us on Facebook

Home   |   New Products   |   Multi-Rotors   |   FPV Airplanes   |   FPV Gimbal   |   FPV Equipment   |   Battery / Chargers   |   Tools & Accessories   |  Site Map

Product Tags: ABCDEFGHIJKLMNOPQRSTUVWXYZ0-9

Copyright © 2015 FPVMODEL.COM®. All Rights Reserved.